revlimiter Badges - Model 60


flat rate shipping

Model 60 Badges

Buy a Model 60 Badge - 58mm Single - $39 USD

Select Badge Size:
Select Badge Color:




Details


  • Gen2 designs with higher quality materials and finishing.
  • Works with most cars. Some models will need holes filled left over from OEM badges.
  • Composed of vinyl and solar-cell quality polyurethane epoxy.
  • Badges are chromed diecast metal. No cheap plastic here.
  • 3M 20 lb tape included with each badge.
  • Completely customizable. Check out some examples here! A fee will apply for custom work.
  • Shipping calculated at checkout. US customers receive Priority Mail. International orders will be sent via EMS or Priority International.

Badges
Badges come in three sizes: 85mm, 58mm and 50mm. These sizes reflect the overall outer diameter of each badge, not the inner logo size.
  • The 58mm are meant for the NA and NB1 nose (fits the NB2 if you fill the holes). It has a wide double bevel around the inner design. This is the most popular size.
  • The 85mm badge is rather large for an older car, but fits the NB2 (01-05) nose well and covers the mounting holes. They can also work well with a larger car or newer.
  • The 50mm are meant to side mount on the fenders and hardtop. The 50mm also fits the NB trunk lid perfectly.
  • All revlimiter Badges are solid metal. They're a level above the OEM chrome plastic they'll likely replace.
Mazda emblem details
The 50mm badge is very low profile by design to keep it close to the body. The 58mm and 85mm have a wider bezel and stick out a bit further.


3m adhesive
Each badge ships with a strip or two of 3M 20 lb mounting tape. It's extremely strong. You can almost pick up the whole car with the stuff! (But seriously, you need to be SURE of the location before you stick the crazy 20 lb tape on your car.)



CUSTOM STUFF!


revlimiter.net Store - custom badges
Want something a little different? Hit the custom badge page to see what I've made so far.

Custom revlimiter Badges!



Installed Photos:


Sharka nose badge
The 58mm nose badge is perfect for the NA Miata nose.


More installed photos here.




About the Ordering Process


Every item in this store is hand-crafted, made one set at a time. Everything is made to your specs. There's no mass production. Because of this, there might be a short delay between placing your order and shipping. Badges usually take a couple days to make and require 24 hours to cure before I can pack and ship. If there's a long wait, I'll contact you via email to inform you of any delays.

California Residents:


California requires the following notice: Badges may contain vinyl and mercury, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.


FAQ


Q: Can I have matching center cap inserts made?!?!
A: Yes! Due to the different sizes that center caps come in, each order would be custom. I'll request measurements in mm to 2 decimal places. You also must actually have center caps on hand. I cannot make the plastic thing (the actual center cap) that fits your wheel. Go to the Center Cap page to read more and place an order.

Q: Can I have a matching keychain made?
A: Sure! Keychains can be seen on the revlimiter Keychain Page.

Q: Why does it cost more to change one of the colors?
A: I keep all of the standard colors in stock. To make a single badge with different colors, that requires me to make a whole batch of them up. Making a whole batch up requires time. And I don't have a whole lot of free time lately. I'm sorry, but I have to charge extra for color changes.

Q: Can I order a matching horn button from you?!??
A: Yes!!! Go to the Horn Button page to see the designs.

Q: I'd really like a rectangular badge. Make it happen.
A: Sure! The mold fee for each new shape is around $1200. If you really want a shape or size not shown above, just let me know. It takes about 3 months for tooling and production in addition to the mold fee.

Q: Can I order one of the special keychain designs (a tach, rainbow kitty, etc)?
A: Sure! The badges use solvent-printed vinyl and can have small detail prints made easily. Just hit the custom order form.

Site Navigation

Latest Blog Posts

Mona Kills Cones
Posted on Wed, 17 Apr 2019 02:03:52 +0000

In the grid.Ramona gets a chance to be driven in anger.
Read more...

ND Gauge RE-install Short Cut
Posted on Mon, 18 Mar 2019 14:42:41 +0000

A slick shortcut to make installing the second set of gauges on your ND much easier.
Read more...

ND Gauges Exist!!!
Posted on Mon, 18 Mar 2019 14:19:10 +0000

Ramona's 17th set of gauges.After making gauges since 2002 and professionally since 2011, I can finally say that I make them for EVERY Miata on the planet! ND gauges are finally out!
Read more...

NA Miata Gas Fumes SOLVED
Posted on Sat, 16 Feb 2019 03:12:46 +0000

The last project in my old house.Further work in eliminating Miata gas fumes. And, spoiler, I FIXED IT!
Read more...

Mooneyes Hot Wheels
Posted on Fri, 25 Jan 2019 21:22:24 +0000

Mooneyes Fiat 500CA quick post about some new Hot Wheels.
Read more...