Quick Release Shootout Part 2: Thin QRs

Part 2!

Part 2!

Here’s Part 2!! Did you miss Part 1 of the revlimiter Quick Release Shootout? Follow the link and check it out.

The Quick Releases

The Quick Releases

The Quick Releases

The Hubs

Click the links above to go straight to a particular quick release review.

Works Bell QRS

Works Bell QRS (Quick Release Spacer)

Works Bell QRS (Quick Release Spacer)

The Works Bell QRS is a thin quick release. It functions via ball bearings and a rotating interlock. The little ears that make it work are also a magnetic safety device – the QR cannot open unless the ears are in the extended position.

This QR does conduct a ground signal, so you don’t need to worry about a dedicated ground wire. Mine also has no fewer than FIVE terminals for various buttons, but I’ve seen models with only one terminal. This Quick Release was discontinued in 2013 and can no longer be purchased. No, mine is not for sale.

QRS dimensions

QRS Dimensions

Thickness: 26.3mm / 1.03 in.
Weight: 102g / 3 oz hangs from the steering wheel; 438g / 15.6 oz total.
Instructions: No
Horn retainer ring: Yes, removable.
Hardware Included: Yes.
Price: I don’t remember. Also, it’s discontinued.

QRS + hub installed.

QRS + hub installed.

Wiring up the horn for this particular QR adapter is no more difficult than wiring a horn to a steering wheel without a quick release. One wire is all it takes.

QR receiver installed in the car.

QR receiver installed in the car.

Unlike the thick QRs seen in Part 1, the thin quick releases usually have most of the guts attached to the car’s hub. The part that hangs off the back of the steering wheel has almost no weight or bulk.

Hub/QR thickness

Hub/QR thickness

With the Daikei standard hub installed, the total hub + QR thickness is ~ 4″ or 101mm. That’s only .75″ thinner than the “thick” options.

Steering wheel to signal distance

Steering wheel to signal distance

The distance from the steering wheel to the turn signal is just under 3″ or 75mm. This is roughly 7/8″ greater than the stock distance. It’s not difficult to reach the turn signal.

As you can see in the video, this quick release requires a bit more work to attach than the thick ones. You have to align the steering wheel, then grab the QR’s ears and rotate it into the locked position. Then you make sure the ears snap back against the QR (yay magnets).

The attachment is very firm and positive. The wheel feels well attached. I’m rather attached to this one too… It’s been in my car for the past eight years. I really like this quick release.

After eight years, I started to see very minor signs of wear inside my WB QRS. That prompted me to look for a spare QR. Then I discovered that they were discontinued. And then I started collecting quick releases. And that’s why you’re reading this blog post.

NRG Slim Quick Release

NRG Slim quick release

NRG Slim quick release

The NRG Slim / Short Quick Release is a thin quick release. It functions purely from friction interlock. This design was actually created by a company called FET in the early 2000s.

NRG slim wires

NRG slim wires

Like the example of NRG thick QR that I received, this Slim one features incorrect horn wiring. Only one wire is incorrect – the ground wire on the steering wheel side (it should be a female disconnect). However, this QR grounds through its own body… so it doesn’t even need a ground wire.

NRG dimensions

NRG dimensions

Thickness: 26.5mm / 1.04 in.
Weight: 105g / 3 oz hangs from the steering wheel; 392g / 14 oz total.
Instructions: No
Horn retainer ring: Yes, removable.
Hardware Included: Yes.
Price: around $95 USD.

Cast + machined?

Cast + machined?

That’s… odd. A cast piece also being CNC machined?

NRG receiver installed.

NRG receiver installed.

Like the WB above, the NRG slim has the receiver attaching to the car. The piece hanging from the steering wheel weighs only 3oz.

Hub + QR thickness

Hub + QR thickness

With the Daikei standard hub installed, the total hub + QR thickness is ~ 4″ or 101mm. That’s only .75″ thinner than the “thick” options.

Wheel to turn signal distance.

Wheel to turn signal distance.

The distance from the steering wheel to the turn signal is just under 3″ or 75mm. This is roughly 7/8″ greater than the stock distance. It’s not difficult to reach the turn signal.

Unfortunately, as you see in the video, my example did not work. The quick release itself was extremely difficult to turn even without anything in it. With both halves together, there was no clearance for anything to turn or move. The half that attaches to the steering wheel needed to be planed down by quite a bit before it would fit inside the receiver.

Since my example did not work, I truly cannot say any more about this quick release adapter.

eBay $16 Thin Quick Release

ebay Thin Quick Release

ebay Thin Quick Release

Since I had the other four, I just couldn’t resist. I had to add a fifth option – the uber-affordable ebay thin QR. It was $16 shipped.

The ebay QR has the same construction as the NRG (FET design) with the puzzle pieces that interlock together. It features a single horn wire and grounds through the QR’s body. And the horn wire? It has the right connectors on the ends.

ebay QR dimensions

ebay QR dimensions

Thickness: 25.5mm / 1.006 in.
Weight: 92g / 3 oz hangs from the steering wheel; 269g / 9 oz total.
Instructions: No
Horn retainer ring: Yes, removable.
Hardware Included: Yes.
Price: $16 shipped.

ebay QR installed

ebay QR installed

So. This little thing is the cheapest, thinnest, and lightest. And the horn wire is right out of the box. And it has all the hardware you need to install it. But keep those little floating hearts at bay. It’s not as perfect as it could be.

The bad news...

The bad news…

THIS is the bad news. The holes are not machined in the correct spots. Only two of the six holes will bolt up to a hub. And before you ask – yes, I also tried the Nardi bolt pattern. That one was worse. The hole pattern on this QR is not correct for either the Momo or Nardi bolt patterns.

If you drilled this quick release out, it would be able to bolt onto a hub. Out of the box? It does not work. You can’t actually drive with it.

Hub + QR thickness

Hub + QR thickness

The piece hanging from the steering wheel weighs only 3oz.

Wheel to signal stalk distance

Wheel to signal stalk distance

With the Daikei standard hub installed, the total hub + QR thickness is ~ 4″ or 101mm.

Since everything did actually work aside from the QR bolting onto the hub correctly, I can give some observations about this quick release. The attachment method is really not difficult. Aligning the wheel into the receiver is easy and spinning the locking collar with one hand is also easy. I would have liked to take a test drive with this quick release, but having only two bolts in the hub (and they’re next to each other, not on opposite sides) made me not want to risk things.

Winners and Losers

It’s a shootout, right? What’s a shootout without some dead bodies? Let’s see who was standing in the end.

ebay Thin Quick Release

ebay Thin Quick Release


ebay $16 QR

  • Good: It was the thinnest, lightest, and cheapest
  • Bad: It didn’t bolt up. The mounting holes on my example were not in the right spots
  • Status: Dead.

NRG Slim quick release

NRG Slim quick release


NRG Slim QR

  • Good: Affordable, thin, and easy to purchase. Lots of enthusiasts love this particular QR.
  • Bad: My example didn’t actually, you know, work.
  • Status: Dead (at least mine is)

Works Bell QRS (Quick Release Spacer)

Works Bell QRS (Quick Release Spacer)


Works Bell QRS

  • Good: Positive attachment, thin, very robust. I truly love this QR. It’s been a reliable friend for around 8 years.
  • Bad: Discontinued and rare. If you want one… you probably can’t find it.
  • Status: Dead.

NRG Gen3 in blue

NRG Gen3 in blue


NRG Gen3

  • Good: Super strong attachment. Affordable and widely available.
  • Bad: SUPER heavy. It adds 1.2 lbs to the steering wheel itself. And my example needed all of the horn wiring redone.
  • Status: Still standing.

Works Bell Rapfix2

Works Bell Rapfix2


Works Bell Rapfix2

  • Good: Super strong attachment. Easy to use. Not overly bulky.
  • Bad: Expensive. If you don’t buy from an Authorized Dealer, you might get a fake.
  • Status: Badass Gunslinger.

Hub Adapters

I have a pair of hub adapters… I might as well review them, right? I did a separate post for those as well. Go to the Hub Comparison to see a Daikei vs a Works Bell.

Hub Adapter Shootout

« | »
  • Legendary says:

    I’m so happy I bought the Works Bell QRS a couple of years ago based on your review of it! It’s a damn shame it has been discontinued. It feels stunningly solid and looks almost OEM in the MX-5/Miata interior. I’ll definitely take good care of mine!

    Keep blogging – I’ve been missing your blog posts! 😀

    • revlimiter says:

      I wish I could find a spare. Such a great QR.

      And thanks! I didn’t intend to have such a long break between blogging. This series of 3 posts took a lot longer than I expected.

  • Fer says:

    Any references of D1 Spec QR? Mine looks like NRG (ver 2.0.) and works fine. Really solid. Price is around 50 GBP.
    http://www.d1spec.com.tw/s/en/2/product/Ball-Lock-Steering-Wheel-Quick-Release-315874.html

    Great shootout, thanks!

  • T.Vo says:

    Not to knock on your experience, but I have two of the NRG thin QR’s and they work well for me. They do have a minuscule of play but only detectable when stationary.

    The quality of Works Bell products is undeniable, but I hate that the finish on the ball bearing ones will be worn pretty easily over time.

    • revlimiter says:

      Honestly, I didn’t intend or desire to paint the NRG thin in a poor light. I know a ton of folks use them and the design looks sound. Mine just… didn’t work from the factory. A small amount of play would have been greatly preferable to less than zero play (one part bigger than the other).

      And yeah, those thick QR designs wear the anodizing off pretty quickly. The blue NRG had visible wear after I finished with my review. I probably had less than 10 attach/release cycles. The WB is fairing a bit better, as it probably is up to 50 cycles by now. Wear is starting to show though.

  • Earl says:

    My problem with WB. 1st I bought the Works Bell Qickfix ll + some additional parts. I paid an “exclusive factory authorized dealer” over $400 in 2016. It’s now 8 months later and nothing shipped. Contacted WB. Answer to bad for you.

  • Bill says:

    I just picked up a Daikei Hub and am planning to get either the Nardi Classic or Momo Prototipo wheel. I also want to run a QR on it. Would the Daikei hub with the Works Rapfix 2 QR be too tall?

  • Leave a Reply to revlimiter